VERTICAL AMPLIFIERS (CH 1 and CH 2) |
Sensitivity | 5mV/div to 5V/div. 1 mV/div to 1V/div (at X5 MAG) |
Attenuator | 10 calibrated steps in 1-2-5 sequence.
Vernier control provides fully adjustable sensitivity between steps, adjustment range 1/1 to 1/2.5 |
Accuracy | +-3% (+-5% at X5 MAG) |
Input Impedance | 1MW+ 3% |
Input Capacitance | 25 pF +- 10pF |
Frequency Response | DC: DC to 100 MHz (-3 dB) on 10mV/Div setting |
X5 MAG | DC to 20 MHz (-3 dB) |
AC | 10Hz to 100 MHz (-3 dB) |
Rise Time | 3.5 ns (Overshoot <=5%) |
Signal Delay Time | Variable |
Square Wave Characteristics | Overshoot less than 5%, 10mV/div range
Other ranges within 5% additional |
Maximum Input Voltage | 400V (DC + AC peak) |
VERTICAL AMPLIFIERS |
Operating Modes | CH 1, CH 2, Dual, Add |
Delay Time Between Channels | Within 1 ns between CH 1 and CH 2 |
Crosstalk | 30:1 at 100 kHz |
SWEEP SYSTEM |
Operating Modes | |
A | A sweep |
B | Delayed B sweep |
B TRIGGERED | B sweep triggered after delay |
A Time Base | |
Sweep Mode | Auto, normal |
Sweep Time: | 5s to 20ns/div., 23 steps in 1-2-5 sequence with variable control |
Accuracy | +-3% |
Hold Off Time | Continuously variable. Adjustment range from normal to 1,5 times the sweep time |
B Time Base | |
Delay Method | Continuous delay. Triggered delay |
Sweep Time | 20ns to 0.5s/div., 23 steps in 1-2-5 sequence |
Accuracy | +-3% |
Hold Off Time | Continuously variable. Adjustment range from normal to 1.5 times the sweep time |
B Time Base | |
Delay Method | Continuous delay. Triggered delay |
Sweep Time | 20 ns. to 0.5s/div., 23 steps in 1-2-5 sequence |
Accuracy | +-3% |
Delay Time | Start point: 0.5 div to + 0.3 div.
End point: 10 div + 1 div |
Delay Jitter | Within 1/10,000 of full scale sweep time |
TRIGGERING |
A Trigger | |
Source | CH 1, CH 2, LINE, EXT |
Sensitivity | 30Hz to 110 MHz |
TV-V | 20Hz - 30kHz |
TV-H | 3 kHz - 100 kHz |
Slope | + or - |
B Trigger | The A trigger is also the B trigger |
EXTERNAL TRIGGER |
Input Impedance | 1 m , 30 pF |
Maximum Input Voltage | 300V (DC + AC peak) |
HORIZONTAL AMPLIFIER |
X-Y Mode | X Axis = CH 1, Y Axis = CH 2 |
Sensitivity | 5 mV/div to 5 V/div, CH 1 and CH 2 |
Accuracy | +- 3% calibrated position, +-6% using x10 MAG |
Frequency Response | DC: DC to 100 MHz (-3 dB) |
X5 MAG | DC to 20 MHz (-3 dB) |
AC | 10 Hz to 100 MHz (-3 dB) |
Rise Time | 3.5 ns (Overshoot <=5%) |
Signal Delay Time | Variable |
Square Wave Characteristics | Overshoot less than 5%, 10 mV/div range |
| Other ranges within 5% additional |
Maximum Input Voltage | 400V (DC + AC peak) |
VERTICAL AMPLIFIERS |
Operating Modes | CH 1, CH 2, Dual, Add |
Delay Time Between Channels | Within 1 ns between CH 1 and CH 2 |
Crosstalk 30:1 at 100 kHz | |
SWEEP SYSTEM |
Operating Modes | |
A | A sweep |
B | Delayed B sweep |
B TRIGGERED | B sweep triggered after delay |
A Time Base | |
Sweep Mode | Auto, normal |
Sweep Time: | 5s to 20ns/div., 23 steps in 1-2-5 sequence with variable control |
Accuracy | +-3% |
Hold Off Time | Continuously variable. Adjustment range from normal to 1.5 times the sweep time |
B Time Base | |
Delay Method | Continuous delay. Triggered delay |
Sweep Time | 20ns. to 0.5s/div., 23 steps in 1-2-5 sequence |
Accuracy | +-3% |
Delay Time | Start point: 0.5 div to + 0.3 div.
End point: 10 div + 1 div |
EXTERNAL TRIGGER |
Input Impedance | 1 m, 30 pF |
Maximum Input Voltage | 300V (DC + AC peak) |
HORIZONTAL AMPLIFIER |
X-Y Mode | X Axis = CH 1, Y Axis = CH 2 |
Sensitivity | 5 mV/div to 5 V/div, CH 1 and CH 2 |
Accuracy | +-3% calibrated position, +-6% using x10 MAG |
Frequency Response | DC to 2 MHz (-3 dB) |
CH I (Y) OUTPUT | |
Output Voltage | Approx. 100mV/div open circuit
Approx. 50 mV/div into 50 |
Freq. Response | 50 Hz to 30 MHz |
Output Impedance | approx. 50 |
CRT |
Type | Rectangular with integral graticule |
Display Area | 8x10 div (1 div = 1 cm) |
Accelerating Voltage | 15 kV |
Phosphor | P31 |
Scale Illumination | None |
Trace Rotation | Electrical, front panel adjustable |
Other Specifications |
Z Axis (Intensity Modulation) | Sensitivity: 3V or greater, TTL level.
Negative polarity increases brightness |
Input Impedance | 15 k |
Usable Freq. Range | DC to 3.5 MHz |
Maximum Input Voltage | 20 V (DC + AC peak) |
CAL/Probe Compensation |
Waveform | Positive going squareware |
Output Voltage | 0.5 V p-p +- 3% |
Frequency | Approx. 1 kHz |
Duty Cycle | 50 +- 5% |
Power Requirements | 100/120/220/240/VAC +- 10%, 50/60 Hz, approximately 55 W |
Dimensions (HxWxD) | 12.76x15.68x5.2'' (324x398x132 mm) |
Weight | 18.7 lbs. (8.5 kg) |
ENVIRONMENT |
Within Specified Accuracy | 50 0 to 95 0 F (10 0 to 35 0 C), 85% maximum RH |
Full Operation | 32 0 to 104 0 F (0 0 to +40 0C), 85% maximum RH |
Storage | -4 0 to 158 0 F (-20 0 to +70 0 C) |
Accessories |
Three Year Warranty |
SUPPLIED: Instruction Manual, Two PR-37A x1/x10/Ref. Probes or equivalent, AC Power Cord, Spare Fuse |
OPTIONAL: PR-32A Demodulator Probe, PR-46A x10 Probe, PR-37A x1/x10/REE Probe, PR-100A x100 Probe, PR-55 High Voltage x1000 Probe, LC-210A Carrying Case |
