| Frequency Characteristics (Standard Waveforms) |
| Sine | 0.1 Hz to 20 MHz |
| Square | 0.1 Hz to 20 MHz |
| Triangle, Ramp | 0.1 Hz to 2 MHz |
| Accuracy | 0.01% (100 ppm) |
| Resolution | 4 digits or 10 mHz |
| Output Characteristics |
| Amplitude Range | 10 mV to 10 Vp-p into 50 Ω |
| Resolution | 3 digits (1000 counts) |
| Amplitude Accuracy | ±2% ± 20 mV of the programmed output from 1.01 V - 10 V |
| Flatness | 0.5 dB at 1 MHz
1 dB to 20 MHz |
| Offset Range | ±4.5 V into 50 Ω, depending on the Amplitude setting |
| Offset Resolution | 10 mV with 3 digits resolution |
| Offset Accuracy | ±2% ± 10 mV into 50 Ω |
| Output Impedance | 50 Ω |
| Output Protection | The instrument output is protected against short circuit or accidental voltage practically available in electronic laboratories, applied to the main output connector |
| Waveform Characteristics |
| Harmonic Distortion | 0 - 20 kHz, -50 dBc
20 kHz - 100 kHz, -45 dBc
100 kHz - 1 MHz, -40 dBc
1 MHz - 20 MHz, -30 dBc |
| Spurious | DC - 1 MHz, < -55 dBc |
| Square Rise/Fall Time | < 20 ns (10% to 90%) at full amplitude into 50 Ω |
| Variable Duty Cycle | 20% to 80% to 2 MHz for Square and 10% - 90% for Triangle |
| Symmetry at 50% | < 1% |
| Operating Modes |
| Continuous | Output continuous at programmed parameters. |
| Triggered | Output quiescent until triggered by an internal or external trigger, then one waveform cycle is generated to programmed parameters, up to 2 MHz |
| Gate | Same as triggered mode, except waveform is executed for the duration of the gate signal. The last cycle started is completed. |
| Trigger Source | Trigger source may be internal, external or manual. Internal trigger rate 10 µs to 10 s. |
| Modulation Characteristics |
| Amplitude Modulation |
| | Internal | Sine signal of 1000 Hz
Variable modulation from 0% to 100% in 1% steps |
| External | 5 Vp-p for 100% modulation, 10 kΩ input impedance, DC to 20 kHz bandwidth. |
| Frequency Modulation |
| | Internal | Sine signal of 1000 Hz |
| External | 5 Vp-p for 100% deviation, 10 kΩ input impedance, DC to 20 kHz bandwidth. |
| Sweep Characteristics |
| Sweep Shape | Linear and Logarithmic, up or down |
| Sweep Time | 10 ms to 50 s. |
| Inputs and Outputs |
| Trigger In | TTL compatible.
Max. rate 2 MHz.
Minimum width 50 ns. |
| Sync Out | TTL pulse at programmed frequency, 50 Ω source impedance. |
| Modulation In | 5 Vp-p for 100% modulation.
10 kW input impedance. DC to > 20 kHz minimum bandwidth. |
| General |
| Dimensions | 8.4'' (213 mm) wide
3.5'' (88 mm) high
8.3'' (210 mm) deep |
| Weight | Approx 2.5 kg. |
| Power | 90 V - 264 V, 30 VA max |
| Temperature |
| | Operating | 0°C to +50°C |
| Non-operating | -10°C to +70°C |
| EMC | According to EN55011 for radiated and conducted emissions. |
| Electrical Discharge Immunity | According to EN55082 |
| Safety Specifications | According to EN61010 |
| Note: Specifications are verified according to the performance check procedures in the technical manual. Specifications not verified in the manual are either explanatory notes or general performance characteristics only. |
Specifications
