CRT |
Type and Acceleration
| 6-inch CRT, 2kV |
| Illumination | Front panel control |
| Z-axis Input | Sensitivity : at least 5V
Polarity : positive going input decreases intensity
Max. input voltage:30V(DC+ACpeak)
Input Impedance : approx. 47kΩ |
VERTICAL SYSTEM |
| Deflection Coefficient and Accuracy | 1mV ~ 2mV/div ±5%,
5mV ~ 20V/div ±3%,
14 steps in 1-2-5 sequence |
| Variable Continuity | 2.5 : 1 ~ min. 50V/div |
| Bandwidth (-3dB) | 1mV ~ 20mV/div: DC~7MHz
5mV ~ 20V/div: DC~30MHz |
| Vertical Mode | CH1, CH2, DUAL (ALT or CHOP) |
| Chopper Frequency | Approx. 250kHz |
Sum or Difference
| CH1+CH2, CH1-CH2 |
Invert
| CH2 |
Input Impedance
| 1MΩ ±2%//approx. 25pF |
Input Coupling
| AC, DC, GND |
Input Voltage
| Max. 400V(DC+ACpeak) |
HORIZONTAL SYSTEM |
Sweep Time
| 0.2μs/div ~ 0.5s/div, 20 steps |
| Variable Continuity | 2.5 : 1 up to 1.25s/div (uncal.) |
Accuracy
| ±3%, ±5% at x5/ x10MAG. ±8% at x 20MAG |
Sweep Magnification
| x5, x10, x20 |
| Max. Sweep Time | 50ns/div (10ns~40ns/div uncal) |
| ALT-MAG Function | Yes |
| HOLD-OFF Time | Variable |
TRIGGER |
Trigger Mode
| AUTO, NORM, TV |
Trigger Source
| VERT, CH1, CH2, LINE, EXT |
| Trigger Coupling | AC, HFR, LFR |
Trigger Slope
| "+"or" - "polarity |
ALT Trigger
| Yes |
| Indicator Trigger LED | Yes |
TV Sync. Separator
| TV-V"-", TV-H" - " |
Trigger Sensitivity
| | GRS-6032A | 20Hz~2MHz | 2MHz~20MHz | 20MHz~30MHz | | CH1, CH2 | 0.5div | 1.5div | 2.0div | | Vert-Mode | 2.0div | 3.0div | 3.5div | | EXT | 200mV | 800mV | 1V |
|
| | TV sync. pulse more than 1 div or 200mV (EXT) |
External Trigger Input
| Input impedance :Approx. 1MΩ//25pF (AC coupling)
Max. input voltage : 400V (DC + ACpeak) |
X-Y OPERATION |
Input
| X-axis : CH1 ; Y-axis : CH2 |
| Sensitivity | 1mV/div ~ 20V/div |
| Bandwidth | X-axis : DC ~ 500kHz (-3dB) |
| X-Y Phase Shift | <3° from DC ~ 50kHz |
DIGITAL STORAGE |
Acquisition Digitizer
| 8 bit ADC x 2 |
Max. Sampling Rate
| 500MSa/s for equivalent time sampling
100MSa/s for normal sampling |
| Storage Bandwidth | Single shot: DC ~ 25MHz
Repetitive: DC ~30MHz |
| Dynamic Range | ±5div |
Memory Length- Acquisition Memory
| 2k words/CH x 2, 1k words/CH(equivalent) |
Memory Length- Save REF Memory
| 1k words/CH x 10 with back-up memory (REF0~REF9) |
| Memory Length- Display Memory | 1k words/CH x 4 waveform(max.) |
| Sweep Time | Equivalent: 0.2μs/div ~ 0.5μs/div
Normal Sample: 1μs/div ~ 0.1s/div
Roll: 0.2s/div ~ 100s/div |
| Sweep Magnification | x 5, x 10, x 20 |
Max.Sweep Time
| 10ns/div |
| MAG Interpolation | DOTS, LINEAR |
| ALT-MAG Function | Yes |
Acquire Mode
| Sample, peak detect(>25ns), Envelop. Persist, Average(2~256) |
| Operation Mode | Auto, Norm, Single, Single-roll, Roll, X-Y, Run/Stop |
| Smoothing Function | Dot joint ON/OFF selectable |
Pre-Trigger
| Pre-trigger 0 ~10div in 0.02div steps |
| X-Y Operation | X-axis: CH1 Y-axis: CH2 |
| Storage Bandwidth | DC~30MHz(-3dB) |
| Display Resolution | H: 100points/div; V: 25points/div;
X-Y: 25 x 25 points/div |
| SAVE/RECALL | |
| Panel Setting | 10 sets(M0 ~M9) |
Waveform
| 10 sets(REF0~REF9) |
| READOUT & CURSOR | |
| Cursor Measurement | ΔV, ΔT, 1/ ΔT |
Readout Intensity
| Adjustable |
| OUTPUT SIGNAL | |
| CH1 Signal Output | Voltage : approx. 20mV/div (with 50Ω terminated) ; Bandwidth : 50Hz ~ 5MHz |
Calibrator Output
| Voltage : 0.5V±3% ; Frequency : approx. 1kHz, square wave |
| INTERFACE | |
| | RS-232C |
POWER SOURCE
| |
| | AC 100V/120V/230V±10%, 50/60Hz |
ACCESSORIES |
| | User manual x 1
Power cord x 1
GTP-060A-4 Probe (10:1/1:1) x 2 |
| DIMENSIONS & WEIGHT | |
| | 275(W) x 130(H) x 370(D) mm
Approx. 8.5kg |
