 |
Instek GSP-830 - 3GHz Spectrum Analyzer
|
 Click to zoom
Instek GSP-830 - 3GHz Spectrum Analyzer
| FEATURES | Low Noise Floor(-117dBm@1GHz, 3k RBW) Autoset Function Sequence Programming Functions ACPR, OCBW, Channel Power, N-dB and Phase Jitter Measurements Pass/Fail Test with Limit Line Editing 5 Markers with Delta Marker, Peak Functions 10 Markers with All Peak Functions Split Windows Allow Separate Settings AC/DC/Battery Multi-Mode Power Operation USB/RS-232C/GPIB(Optional) Interface Direct VGA Output 6.4" TFT Color LCD, Resolution: 640x480 Compact Size, 330(W) x 170(H) x 340(D) mm Light Weight of 6kg Without Options Optional Tracking Generator Optional Preamplifier |
 |
 Specifications
FREQUENCY | | Frequency Range | 9kHz ~ 3GHz | | Aging Rate | ± 10ppm, 0~50°C, 5ppm/yr | | Span Range | 2kHz ~ 3GHz in 1-2-5 sequence, full span, zero span | | Phase Noise | -80dBc/Hz @1GHz 20kHz offset typical | | Sweep Time Range | 50ms ~ 25.6s | RESOLUTION BANDWIDTH | | RBW Range | 3kHz, 30kHz, 300kHz, 4MHz | | RBW Accuracy | 15% | | Video Bandwidth Range | 10Hz ~ 1MHz in 1-3 steps | AMPLITUDE | | Measurement Range | -103dBm ~ +20dBm: 1MHz ~ 15MHz, Ref.Level @ -30dBm
-117dBm ~ +20dBm: 15MHz ~ 1GHz, Ref.Level ≧-110dBm
-114dBm ~ +20dBm: 1GHz ~ 3GHz, Ref.Level ≧-110dBm
(Span = 50kHz, RBW = 3kHz) | | Overload Protection | Max. +30dBm, ±25VDC | | Reference Level Range | -110dBm ~ +20dBm | | Accuracy | ±1dB @100MHz | | Frequency Flatness | ±1dB | | Display Range Linearity | ±1dB over 70dB | DYNAMIC RANGE | | Average Noise Floor | <-135±1dBm/Hz: 1MHz ~ 15MHz, Ref.Level @ -30dBm
<-149dBm/Hz, typical -152dBm/Hz: 15MHz ~ 1GHz, Ref.Level ≧-110dBm
<-146dBm/Hz, typical -149dBm/Hz: 1GHz ~ 3GHz, Ref.Level ≧-110dBm | | Third Inter-Modulation | <-70dBc RF Input @-40dBm, Ref.Level @-30dBm | | Harmonic Distortion | <-60dBc RF Input <-40dBm , Ref.Level @-30dBm | | Non-Harmonic Spurious | <-93dBm, 1MHz ~ 15MHz, Ref.Level @-30dBm
<-107dBm ~ +20dBm: 15MHz ~ 1GHz, Ref.Level ≧-110dBm
<-104dBm ~ +20dBm: 1GHz ~ 3GHz, Ref.Level ≧-110dBm
(Span = 50kHz, RBW = 3kHz) | GENERAL | | Display | 640 x 480 high resolution TFT color LCD | | Split Windows | Active Window: Upper, Lower or Alternate (two simultaneously sweeping windows) | | Markers | 10 Markers for peaks: 5 normal-delta marker pairs
Functions: Delta, To Peak, To Minimum, Peak Track, Peak Table, Peak Sort | | Trace Detection | 3 traces with Peak, Maximum hold, Freeze, Average, Trace math | | Power Measurement | ACPR, OCBW, Channel Power, N dB and Phase Jitter | | Autoset Function | Auto tuning the measurement result for observation | | Trigger | Conditions: Video, External (Positive-going, +5V TTL external signal)
Mode: Normal, Single, Continuous
| | Sequence | Automated test by user-defined macros without any remote controller, 10 Sequential macro set and 10 macros per each set, Variable delays and wait-to-go facilitate automated measurement, Do-sequence links and nests different sequence sets. | CONNECTORS | RF Input
| N female, 50Ω nominal
RF input VSWR: <2:1, @0dBm Reference Level | | External Reference | Type: BNC female | | Clock Input | 1M, 1.544M, 2.048M, 5M, 10M, 10.24M, 13M, 15.36M, 15.4M, 19.2MHz | | Reference Clock Output | Type: BNC female, 10MHz | | DC Input (DC Power Operation) | Jack : 5.5mm, 12V | | DC Output (for GAP-801) | Type: SMB Male, outputs +9V/100mA Max. | INTERFACE | | RS-232C | Sub-D 9 pins female | | USB Connector | USB Host/Device full speed supported | | VGA Output | Front panel: Type A receptacle for USB flash devices | | Option: GPIB Interface | Fully programmable with IEEE 488.2 compliance | | POWER SOURCE | | | | AC 100 ~ 240V, 50/60Hz | | ACCESSORIES | | | User Manual x 1
Power Cord x 1
USB Cable (Type A plug to Type mini-B plug) x1 | | DIMENSIONS & WEIGHT | | | 330(W) x 170(H) x 340(D) mm
Approx. 6kg |
|
|
|
|
