 |
BK Precision Electrical Testers
|
 Click to zoom |
This insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It is also useful for safety testing of TV sets and appliances to assure no hazardous leakage current. The voltage and resistance ratings for insulation testing are often specified for the product to be tested.
Test insulation resistance
Measure AC voltage to 600V
Battery powered
1000V test voltage
Test up to 2000M ohms
|
Click to zoom |
The 301 is intended to be used with an AC Current Clamp Meter. It provides temporary separation of conductors to facilitate measurement of current. Most 120Vac devices use a two conductor power cord which makes it difficult to isolate a single conductor to make a current measurement. A single conductor is required to make a measurement because a two conductor measurement will cancel each other out.
Features
X10 Mode allows for more accurate measurements of low amperage devices
Direct reading in X1 mode
2mm Voltmeter measurement points
Integrated ground conductor (three pronged US standard plug)
15 amp capacity
Applications
Monitor a devices power consumption
Measure surge current
|
Click to zoom |
The model 302 is a 3 Phase Presence and Rotation Meter combined with a 3 Phase Motor Rotation Tester. It is the quickest and easiest way for servicing, repairing and electrical maintenance of 3 phase systems and 3 phase rotating machinery. It can be utilized on a 3 Phase Powered System (the supply side) or on a Three Phase Un-powered Motor (the load side) without having to worry about damage to the tester. When utilized on a 3 Phase Powered System, the instrument is then utilized as a 3 Phase Presence and Rotation Indicator. When utilized on a Three Phase Un-powered Motor, the instrument is then utilized as a 3 Phase Motor Rotation Tester. When utilized on a 3 Phase Powered System, this instrument is a rotary field indication instrument which display all three Phase by lighting up it's corresponding LED. It displays the rotation (clockwise or counter-clockwise) on a LED. When utilized on a 3 Phase Un-powered Motor, it is also possible to determine the motor connections U, V, W without a live circuit to avoid subsequent damages of e.g. pumps to reversed motor rotation. It displays the rotation (clockwise or counter-clockwise) on a LED. - Indicates Phase Presence
- Indicates Phase Rotation
- Indicates Motor Rotation / Wiring
- Indicates Battery Status
- Phase Rotation and Motor Rotation Indication works from as low as 1Vac
- Small and rugged enclosure
- Phase and Motor Rotation Indicator works from as low as 1Vac
- Color Coded test Leads
- Phase Presence Indication from as low as 100Vac
- Very Low Consumption
- Fused
- Lightweight, Robust & Compact.
- Works from 2 Hz to 400Hz Sine
- IEC/EN 61010-1 CAT III / 600V / CE
|
|
Click to zoom |
This insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It is also useful for safety testing of TV sets and appliances to assure no hazardous leakage current. The voltage and resistance ratings for insulation testing are often specified for the product to be tested.
Test insulation resistance
Measure AC voltage to 600V
Battery powered
500V test voltage
Test up to 1000M ohms
|
Click to zoom |
The model 307A insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It is also useful for safety testing of TV sets and appliances to assure no hazardous leakage current. The voltage and resistance ratings for insulation testing are often specified for the product to be tested.
Test insulation to 400Mohms
Selectable 250V, 500V, or 1000V insulation test
Low ohm resistance test ranges 500ohm & 3ohm
200mA Short circuit test
Extra rugged integral carrying case
Locking switch for extended testing
Live circuit indicator warns of safety hazard
Volt meter to 600Vac
Battery test feature
Overload protection
IEC 1010-1 Cat III 600V / CE
|
Click to zoom |
The model 308A insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It is also useful for safety testing of TV sets and appliances to assure no hazardous leakage current. The voltage and resistance ratings for insulation testing are often specified for the product to be tested.
Test insulation to 2000Mohms
Selectable 250V, 500V, or 1000V insulation test
Low ohm resistance test ranges 2Kohm & 20ohm
3 1/2 Digit LCD
200mA Short circuit test
Extra rugged integral carrying case
Locking switch for extended testing
Live circuit indicator warns of safety hazard
Volt meter to 600Vac
Overload protection
IEC 1010-1 Cat III 600V / CE
|
Click to zoom |
The model 309 Digital Earth Resistance Meter is a small, compact, battery powered, professional meter. This easy-to-use meter is invaluable to electricians and contractors who need to ensure the "ground" quality and effectiveness of buildings, structures, equipment or electrical systems. A good earth ground is required for new buildings or structures needing to pass required electrical codes. Older buildings can lose a good, effective earth ground connection over time. This can happen after a building or structure has been struck by lightning. Measure Earth Resistance (20/200/2000 ohm ranges) Measures Earth AC Voltage to 200VAC (40 to 500Hz) Timed function test turns output off after a 3 to 5 min continuous test 2mA Measuring current measures resistance without tripping circuit breakers Data Hold Small Light Weight Auto Power Off IEC 1010 CAT III 200V / CE Included: Test Leads, Auxiliary Earth Spikes, Carrying Case and Batteries .
|
Click to zoom |
The model 310 Digital Milli-Ohm Meter is used to ensure continuity and integrity of a wire, cable, conduit or any electrical connection. The 310 has a display resolution of 100 micro-ohms and has a professional four wire Kelvin test lead set included to ensure accurate readings. The heavy duty case has a rubber seal to make the unit water resistant and a convenient shoulder strap. Four wire Kelvin lead measurements Over-voltage and over-temperature protection 5 ranges with 100µ ohm max resolution Water resistant case with shoulder strap Auto Power Off IEC/EN 61010-1 / CE Included: 4-Wire Kelvin Leads, Carrying Case with Shoulder Strap and Batteries
|
Click to zoom |
The HV-44A is a self-contained instrument that measures high DC voltages up to +40KV. This probe is typically used to measure high voltages in TV sets, power supplies, laboratories and for general high voltage commercial applications.
|
Click to zoom |
B+K Precision's SenseLiteTM high intensity pocket flashlight can be used to detect the presence of AC voltage at a socket, switch or wire. Simply place the flashlight near the area to be tested and press the power button. If there is an AC voltage present, the red LED will shine brightly. B+K Precision's SenseLiteTM offers a number of outstanding features including:
•AC Voltage Detection (detects AC voltage from 40VAC to 300VAC)
•Water Resistant
•Long Battery Life
•No Lithium Battery, uses standard Alkaline AAA Battery
•100,000 hr Bulb
|
|
|
|
|
